update problems

cosmo2z · Post by **cosmo2z** » Sat Mar 31, 2007 3:50 pm

ok i havnt even played silkroad as its not letting me update :banghead:

i downloaded it of the website and every time it trys to update from version 1.59 it gets to 4% complete and an error message pops up saying '' update not completed[error code- 4]''

please help as it is infuriating!!!!!

Fracture · Post by **Fracture** » Sat Mar 31, 2007 4:30 pm

Double post, see below.

Fracture · Post by **Fracture** » Sat Mar 31, 2007 4:31 pm

cosmo2z wrote:ok i havnt even played silkroad as its not letting me update
i downloaded it of the website and every time it trys to update from version 1.59 it gets to 4% complete and an error message pops up saying '' update not completed[error code- 4]''

please help as it is infuriating!!!!!

Aha, finally, someone has the same error!

Fracture wrote:Start -> Run -> 'services.msc'

Look for DHCP CLIENT and make sure it is set to AUTOMATIC and it is STARTED

If it isn't the former, then Right click DHCP CLIENT, select properties, and set it to AUTOMATIC, then START it; Close services

Start -> Run -> 'msconfig'

Navigate to the BOOT.INI tab

Select /SAFEBOOT and check MINIMAL

Save and Exit; Restart

Start -> Run -> Control Panel -> Network Connections

Right click and disable your ETHERNET (Local area connection) not your 1394

Unplug your modem; Wait 10-15 seconds.

Plug your modem back in

Enable your ETHERNET and let the connection resume

Start -> Run -> 'cmd'

Once at the command prompt type the following:
ipconfig /renew

After your connection resolves, close the command prompt

Start -> Run -> 'msconfig'

Navigate to BOOT.INI and de-select /SAFEBOOT

Save, Exit, Restart

Please let me know if this fixes your problem, it fixed mine!

cosmo2z · Post by **cosmo2z** » Sat Mar 31, 2007 4:34 pm

im using wireless so i wont be able to start ethernet

Fracture · Post by **Fracture** » Sat Mar 31, 2007 4:35 pm

cosmo2z wrote:im using wireless so i wont be able to start ethernet

You don't have access to your wireless router?

cosmo2z · Post by **cosmo2z** » Sat Mar 31, 2007 4:37 pm

yup i do, im a noob when it comes to networking ! :oops:

Fracture · Post by **Fracture** » Sat Mar 31, 2007 4:39 pm

cosmo2z wrote:yup i do, im a noob when it comes to networking !

Ok, do you have access to your modem? This is where the connection originates.

cosmo2z · Post by **cosmo2z** » Sat Mar 31, 2007 4:40 pm

i read another post on the forum and it said about disableing firewall and virus protection so im trying that 1st, ill give your suggestion a shot in a minute

Fracture · Post by **Fracture** » Sat Mar 31, 2007 4:41 pm

cosmo2z wrote:i read another post on the forum and it said about disableing firewall and virus protection so im trying that 1st, ill give your suggestion a shot in a minute

Well, I hope that helps, but I was getting '[Error Code(4)]' without anything turned on as well, hence I specialize in this solution.

cosmo2z · Post by **cosmo2z** » Sat Mar 31, 2007 4:42 pm

yes i do have access to it

cosmo2z · Post by **cosmo2z** » Sat Mar 31, 2007 4:43 pm

its got half way through 4% now im just watching it to see how its going ill let you know if it gets past it

cosmo2z · Post by **cosmo2z** » Sat Mar 31, 2007 4:46 pm

did the error happen for you at 4% as well ???

Fracture · Post by **Fracture** » Sat Mar 31, 2007 4:47 pm

cosmo2z wrote:did the error happen for you at 4% as well ???

It happened for me at 2%, 19%, 31%, 49%, 52%, etc...

Silkroad Online Forums

update problems

update problems

Re: update problems

Re: update problems